|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Features Output IP3: +40 to +42 dBm Gain: 12.5 dB @ 2150 MHz 50% PAE @ +28 dBm Pout +17.5 dBm W-CDMA Channel Power@ -45 dBc ACP Single +5V Supply Industry Standard SOT89 Package 8 AMPLIFIERS - SMT Typical Applications The HMC454ST89 is ideal for applications requiring a high dynamic range amplifier: * GSM, GPRS & EDGE * CDMA & W-CDMA * CATV/Cable Modem * Fixed Wireless & WLL Functional Diagram General Description The HMC454ST89 is a high dynamic range GaAs InGaP Heterojunction Bipolar Transistor (HBT) 1/2 watt MMIC amplifier operating between 0.4 and 2.5 GHz. Packaged in a low cost industry standard SOT89, the amplifier gain is typically 17.8 dB from 0.8 to 1.0 GHz and 12.5 dB from 1.8 to 2.2 GHz. Utilizing a minimum number of external components and a single +5V supply, the amplifier output IP3 can be optimized to +40 dBm at 0.9 GHz or +42 dBm at 2.0 GHz. The high output IP3 and PAE makes the HMC454ST89 an ideal driver amplifier for Cellular/PCS/3G, WLL, ISM and Fixed Wireless applications. Electrical Specifications, TA = +25C, Vs= +5V, (note 1) Parameter Frequency Range Gain Gain Variation Over Temperature Input Return Loss Output Return Loss Output Power for 1dB Compression (P1dB) Saturated Output Power (Psat) Output Third Order Intercept (IP3) (note 2) Noise Figure Supply Current (Icq) 37 22 16 Min. Typ. 824 - 960 17.8 0.008 9 13 24.5 25.5 40 8 150 38 24 0.016 11 Max. Min. Typ. 1800 - 2000 12.5 0.008 7 21 27 28.5 41 6.5 150 38 24 0.016 11 Max. Min. Typ. 2000 - 2200 12.5 0.008 12 19 27.5 28.5 42 5.2 150 0.016 Max. Units MHz dB dB / C dB dB dBm dBm dBm dB mA Note 1: Specifications and data reflect HMC454ST89 measured using the respective application circuits for each designated frequency band found herein. Contact the HMC Applications Group for assistance in optimizing performance for your application. Note 2: Two-tone input power of 0 dBm per tone, 1 MHz spacing. 8 - 250 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Broadband Gain & Return Loss @ 900 MHz 25 20 15 RESPONSE (dB) 10 Gain vs. Temperature @ 900 MHz 20 19 18 17 8 AMPLIFIERS - SMT 8 - 251 GAIN (dB) 5 0 -5 -10 -15 -20 0.4 0.5 0.6 0.7 S21 S11 S22 16 15 14 13 12 11 10 +25 C +85 C -40 C 0.8 0.9 1 1.1 FREQUENCY (GHz) 1.2 1.3 1.4 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 Input Return Loss vs. Temperature @ 900 MHz 0 -5 RETURN LOSS (dB) Output Return Loss vs. Temperature @ 900 MHz 0 -10 RETURN LOSS (dB) -5 -10 -15 +25 C +85 C -40 C -15 -20 +25 C +85 C -40 C -25 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 -20 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 P1dB vs. Temperature @ 900 MHz 30 29 28 27 P1dB (dBm) 26 25 24 23 22 21 20 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 +25 C +85 C -40 C Psat vs. Temperature @ 900 MHz 30 29 28 27 PSAT (dBm) 26 25 24 23 22 21 20 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 +25 C +85 C -40 C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 8 AMPLIFIERS - SMT Output IP3 vs. Temperature @ 900 MHz 44 43 42 41 OIP3 (dBm) 40 39 38 37 36 35 34 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 +25 C +85 C -40 C Noise Figure vs. Temperature @ 900 MHz 15 14 13 NOISE FIGURE (dB) 12 11 10 9 8 7 6 5 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 +25 C +85 C -40 C Reverse Isolation vs. Temperature @ 900 MHz 0 -5 -10 ISOLATION (dB) -15 -20 -25 -30 -35 -40 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 +25 C +85 C -40 C Gain, Power & IP3 vs. Supply Voltage @ 900 MHz GAIN (dB), P1dB (dBm), PSAT (dBm), OIP3 (dBm) 45 40 35 30 25 20 15 10 5 4.5 4.75 5 Vs (Vdc) 5.25 5.5 GAIN P1dB PSAT OIP3 ACPR vs. Supply Voltage @ 880 MHz CDMA IS95, 9 Channels Forward -30 -35 -40 -45 ACPR (dBc) -50 -55 -60 -65 -70 -75 -80 7 8 9 10 11 12 13 14 15 16 17 18 19 Channel Output Power (dBm) Source ACPR 5.5V CDMA IS95 Frequency : 880 MHz Integration BW: 1.228 MHz Forward Link, 9 Channels 4.5V 5.0V 8 - 252 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Broadband Gain & Return Loss @ 1960 MHz 25 20 15 RESPONSE (dB) 10 5 0 -5 -10 -15 -20 -25 1 1.2 1.4 1.6 1.8 2 2.2 2.4 FREQUENCY (GHz) 2.6 2.8 3 S21 S11 S22 Gain vs. Temperature @ 1960 MHz 15 14 13 12 11 10 9 8 7 6 5 1.7 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 +25 C +85 C -40 C 8 AMPLIFIERS - SMT 8 - 253 Input Return Loss vs. Temperature @ 1960 MHz 0 Output Return Loss vs. Temperature @ 1960 MHz 0 GAIN (dB) -5 RETURN LOSS (dB) RETURN LOSS (dB) -5 +25 C +85 C -40 C -10 -10 +25 C +85 C -40 C -15 -15 -20 -20 1.7 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 -25 1.7 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 P1dB vs. Temperature @ 1960 MHz 32 31 30 29 P1dB (dBm) 28 27 26 25 24 23 22 1.7 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 +25 C +85 C -40 C Psat vs. Temperature @ 1960 MHz 32 31 30 29 PSAT (dBm) 28 27 26 25 24 23 22 1.7 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 +25 C +85 C -40 C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 8 AMPLIFIERS - SMT Output IP3 vs. Temperature @ 1960 MHz 44 43 42 41 OIP3 (dBm) 40 39 38 37 36 35 34 1.7 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 +25 C +85 C -40 C Noise Figure vs. Temperature @ 1960 MHz 10 9 8 NOISE FIGURE (dB) 7 6 5 4 3 2 1 0 1.7 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 +25 C +85 C -40 C Reverse Isolation vs. Temperature @ 1960 MHz 0 Gain, Power & IP3 vs. Supply Voltage @ 1960 MHz GAIN (dB), P1dB (dBm), PSAT (dBm), OIP3 (dBm) 45 40 35 30 25 20 15 10 5 4.5 4.75 5 Vs (Vdc) 5.25 5.5 GAIN P1dB PSAT OIP3 -5 ISOLATION (dB) +25 C +85 C -40 C -10 -15 -20 -25 1.7 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 8 - 254 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz ACPR vs. Supply Voltage @ 1.96 GHz CDMA 2000, 9 Channels Forward -40 -45 -50 ACPR (dBc) -55 -60 -65 -70 -75 -80 -85 2 4 6 8 10 12 14 16 18 20 22 Channel Output Power (dBm) Source ACPR 5.0V 5.5V CDMA2000 Rev. 8 Frequency : 1.96 GHz Integration BW: 1.228 MHz Forward Link, SRI, 9 CHANNELS ACPR vs. Supply Voltage @ 2.14 GHz W-CDMA, 64 DPCH -30 -35 -40 ACPR (dBc) WCDMA Frequency : 2.14 GHz Integration BW: 3.84 MHz 64 DPCH 8 AMPLIFIERS - SMT 8 - 255 4.5V -45 -50 -55 5.5V 4.5V 5.0V -60 -65 Source ACPR -70 0 2 4 6 8 10 12 14 16 18 20 Channel Output Power (dBm) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 8 AMPLIFIERS - SMT Absolute Maximum Ratings Collector Bias Voltage (Vcc) RF Input Power (RFin)(Vs = +5.0 Vdc) Junction Temperature Continuous Pdiss (T = 85 C) (derate 13.6 mW/C above 85 C) Thermal Resistance (junction to ground paddle) Storage Temperature Operating Temperature +6.0 Vdc +20 dBm 150 C 0.890 W 73 C/W -65 to +150 C -40 to +85 C Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: MOLDING COMPOUND MP-180S OR EQUIVALENT. 2. LEAD MATERIAL: Cu w/Ag SPOT PLATING. 3. LEAD PLATING: 80Sn/20Pb 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. 8 - 256 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Pin Descriptions Pin Number Function Description This pin is AC coupled. Off chip matching components are required. See Application Circuit herein. Interface Schematic 8 AMPLIFIERS - SMT 8 - 257 1 RFIN 3 RFOUT RF output and DC Bias input for the output amplifier stage. Off chip matching components are required. See Application Circuit herein. 2,4 GND These pins & package bottom must be connected to RF/DC ground. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 8 AMPLIFIERS - SMT 900 MHz Application Circuit, Compact Layout This circuit was used to specify the performance for 894-960 MHz operation. This circuit will satisfy many applications from 700 to 1200 MHz. Contact the HMC Applications Group for assistance in optimizing performance for your application. TL1 Impedance Physical Length Electrical Length 50 Ohm 0.050" 2.5 Recommended Component Values L1, L2 L3 R1 C1 C2 C3 C4, C6 C5 1 nH 36 nH 5.1 Ohms 8 pF 22 pF 2.7 pF 100 pF 2.2 F PCB Material: 10 mil Rogers 4350, Er = 3.48 8 - 258 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 900 MHz Evaluation PCB 8 AMPLIFIERS - SMT List of Materials for Evaluation PCB 107755* Item J1 - J2 J3 -J4 C1 C2 C3 C4, C6 C5 L1, L2 L3 R1 U1 PCB** Description PC Mount SMA Connector DC Pins 8 pF Capacitor, 0402 Pkg. 22 pF Capacitor, 0402 Pkg. 2.7 pF Capacitor, 0402 Pkg. 100 pF Capacitor, 0402 Pkg. 2.2 F Capacitor, Tantalum 1 nH Inductor, 0402 Pkg. 36 nH Inductor, 0402 Pkg. 5.1 Ohms HMC454ST89 Linear Amp 107753 Evaluation PCB, 10 mils The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. ** Circuit Board Material: Rogers 4350, Er = 3.48 * Reference this number when ordering complete evaluation PCB. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 8 - 259 v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 8 AMPLIFIERS - SMT 1960 & 2140 MHz Application Circuit This circuit was used to specify the performance for 1800-2000 and 2000-2200 MHz operation. This circuit will satisfy many applications from 1700 to 2500 MHz. Contact the HMC Applications Group for assistance in optimizing performance for your application. TL1 Impedance Physical Length Electrical Length 50 Ohm 0.32" 34 TL2 50 Ohm 0.10" 11 TL3 50 Ohm 0.17" 18.5 Recommended Component Values L1 C1 C2 C3 C4 C5 8.2 nH 1 pF 1.2 pF 3 pF 100 pF 2.2 F PCB Material: 10 mil Rogers 4350, Er = 3.48 8 - 260 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 1960 & 2140 MHz Evaluation PCB 8 AMPLIFIERS - SMT List of Materials for Evaluation PCB 107749* Item J1 - J2 J3 - J4 C1 C2 C3 C4 C5 L1 U1 PCB** Description PC Mount SMA Connector DC Pins 1.0 pF Capacitor, 0402 Pkg. 1.2 pF Capacitor, 0402 Pkg. 3.0 pF Capacitor, 0402 Pkg. 100 pF Capacitor, 0402 Pkg. 2.2 F Capacitor, Tantalum 8.2 nH Inductor, 0402 Pkg. HMC454ST89 107747 Evaluation PCB, 10 mils The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. ** Circuit Board Material: Rogers 4350, Er = 3.48 * Reference this number when ordering complete evaluation PCB. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 8 - 261 v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 8 AMPLIFIERS - SMT Alternative 900 MHz Application Circuit, Optimal OIP3 Layout This alternate application circuit for 900 MHz applications features a resonating I/O structure on the PCB that, while using more PCB area, will improve output IP3 from +40 dBm to +42 dBm. This circuit will satisfy many applications from 700 to 1200 MHz as the typical performance below demonstrates. Contact the HMC Applications Group for assistance in optimizing performance for your application. Recommended Component Values L1 TL1 Impedance Physical Length Electrical Length 50 Ohm 0.35" 18 TL2 50 Ohm 0.05" 2.5 TL3 50 Ohm 0.53" 27 C1 C2, C6 C3 C4 C5 18 nH 4 pF 10 pF 3 pF 100 pF 2.2 F PCB Material: 10 mil Rogers 4350, Er = 3.48 Broadband Gain & Return Loss 25 20 15 RESPONSE (dB) 10 5 0 -5 -10 -15 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) 1.2 1.3 1.4 S21 S11 S22 Output IP3 & P1dB OUTPUT IP3 (dBm), OUTPUT P1dB (dBm) 50 45 40 35 30 25 20 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 OIP3 OP1dB 8 - 262 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0404 MICROWAVE CORPORATION HMC454ST89 InGaP HBT 1/2 WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Alternate 900 MHz Evaluation PCB 8 AMPLIFIERS - SMT List of Materials Item J1 - J2 J3 - J4 C1 C2, C6 C3 C4 L1 U1 PCB* Description PC Mount SMA Connector DC Pins 4 pF Capacitor, 0402 Pkg. 10 pF Capacitor, 0402 Pkg. 3.0 pF Capacitor, 0402 Pkg. 100 pF Capacitor, 0402 Pkg 18 nH Inductor, 0402 Pkg. HMC454ST89 107750 Evaluation PCB, 10 mils The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. * Circuit Board Material: Rogers 4350, Er = 3.48 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 8 - 263 |
Price & Availability of HMC454ST89 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |